Thursday, May 05, 2011

The Slow Slog

Distance: 109/2117 Day: 18

Even I'm not buying the "slow days are good days for the boat and crew" line any more. The first half of the trip -- despite one day of being becalmed -- we averaged 5 knots/day. Now we're averaging more like 4... when we are lucky. Our landfall target date slipped today into May 10 soonest. This wind needs to hold or freshen a bit, or we are seriously going to run out of patience.

Food, water, and fuel in good supply.

Spinnaker busted yesterday. Actually, it was a fitting way up at the top in the sock. Two swivels separated by a 10" stainless steel bolt. The bolt was showing signs of rust and bent. Yesterday, it simply snapped. DrC and I agree that the thing was clearly under-powered, a much stronger fitting is required. We may eventually purchase a replacement, but obviously that it not possible in the middle of the Pacific. So DrC built us a replacement out of spectra line. Here's the thing about boats... if this line works and does not case chafe or cause other problems, we may never replace the stainless. Sometimes the fix is better than the original. Almost inevitably when you replace stainless with spectra, that turns out to be the case.

Last night was for me one of the hardest nights on helm. The winds varied between 10 to 28 as we passed under and through squall after squall after squall. None of them lasted particularly long, but the cumulative total of steering and worry took its toll. You can not be complacent passing through these squalls. At any time the wind can do some insane thing and pop up to 35 and even considerably higher. We haven't seen it *knock on wood* but that does not mean we don't believe that it can happen. Each time the wind starts to rise, you have to reef. When the wind drops, you shake out the reef. Now most of the night we were able to actually lumber along with a single reef, but there was a memorable squall where I was pulling in the jib, taking a second reef, and untangling a reefing line from the wind generator while perched precariously on a stanchion all the while we bounded over and around wind waves in 27 knots. Of course, literally the moment I had all this in place, the wind dropped to 11. *sigh* It took nearly a half hour for the adrenaline to clear my system. Yes, Mom, I had on a safety harness. It made me seriously reconsider my passage drinking policy.

I made sour dough yesterday. Now, let's be clear. I've had sour dough starter and made bread from it for years. The bread was delicious and tasted faintly sour. This, however, was the first loaf I have ever made that looked and tasted like real sour dough bread. Real Sour Dough Bread for a western American is SOUR. It comes from San Francisco or Seattle, the tang is evident in both the aroma and the taste, and has a crisp crunchy crust. We think the trick was that I made it the night before and let it rise incredibly slowly all night. Then I proofed it and let it rise for another 5 or 6 hours. It smelled divine. It tasted great. The family inhaled it. It's gone. Now I need to figure out how to recreate it. I'll give that a try tonight. I really have nothing else to do.

~ Toast
May 5, 18:00 UTC

12 comments:

jude said...

Your posts are so interesting, funny, creative. Love keeping up with you.

Judy , from the Michigan Conger clan

greatmetal said...

Thanks for sharing the best information and suggestions, If you are looking for the best Stainless Steel 304 Hex Bolt, then Great steel & metals. Highly energetic blog, I’d love to find out some additional information.

oshwin said...

I agree with a lot of the points you made in this article. If you are looking for the ASTM B444 UNS N06625, then visit Oshwin. I love your content, they are very nice and very useful to us and this text is worth everyone’s attention.

highstrengthsteelplates said...

Your blog is awfully appealing. I am contented with your post. I regularly read your blog and its very helpful. If you are looking for the best stainless steel sheet, then visit STANCOR ALLOYS INC. Thanks! I enjoyed this blog post.

vihasteel said...

Really helpful down to the ground, happy to read such a useful post. I got a lot of information through it and I will surely keep it in my mind. Keep sharing. If you are looking for some useful data and information regarding stainless steel threaded rod manufacturers then visit VIHA STEEL & FORGING.

duplexpipessteel said...

In this post, all information and suggestions are helpful for us. Keep sharing more Post like this. duplex tube suppliers For more information relevant things please visit Perfect Impex.

jigneshsteel said...

After find this blog, I found Lots of information which increase my knowledge till to starting point. I am happy to find this kind of blog ss bolts and nuts Must visit Jignesh Steel for more info.

nickelalloysonline said...

It was such a good post. Visit stainless steel flange bolts. Thanks for sharing.

Regal Sales Corporation said...


Wonderful Article, which define very interesting information about the topic.Thanks for taking your time to share A193 B7 If you wants more related services then must visit Regal Sales Corporation.

rexaltubes said...

After read this post I understand new things and Knowledge of this. I find latest information about this topic carbon steel pipe suppliers If you wants relevant services then visit Rexal Tubes.

ashtapad said...



Nice reading, I love your content. This is really a fantastic and informative post. Keep it up and if you are looking for Stainless Steel Pipe Fittings manufacturers in india then visit Ashtapad Overseas.

Manifold Pipe Solution Inc. said...


Hi there to everybody, it’s my first go to see of this web site; this weblog consists of awesome and in fact good stuff for visitors. Hurrah, that’s what I was exploring for, what stuff! Existing here at this blog, thanks admin of this web site. You can also visit stainless steel 304 round bar for more fastenersonline related information and knowledge.